Earthquake · Saturday, September 12, 2026
Magnitude 1.4 earthquake 4 km E of Lennox, CA
A magnitude 1.4 (micro) earthquake struck 4 km E of Lennox, CA on Saturday, September 12, 2026 at , at a depth of 18 km (shallow).
- Magnitude
- 1.4Micro
- Depth
- 18km · shallow
- Time
- Epicenter
- 33.93° N
118.31° W - Aftershocks so far
- 0within 250 km
- Largest aftershock
- —
58 days ago · USGS id ci41545360 · last revised
The full globe opens the 3D cross-section: the hypocenter at depth, the plate boundary and subducting slab where there is one, the aftershock sequence as it grows, and the sea floor around an offshore epicenter.
What a magnitude 1.4 means
Micro earthquakes are generally not felt and are recorded only by seismographs.
A magnitude 1.4 releases about 31 times the seismic energy of a magnitude 0.4, roughly the energy of 0 tonnes of TNT. Magnitude measures the energy released at the source; how hard the ground shook at any one place depends on distance, depth and local geology, and is reported separately as intensity.
Shallow earthquakes (under 70 km) release their energy close to the surface, so shaking is stronger and more damaging near the epicenter than for a deeper quake of the same size.
Nearby earthquakes and aftershocks
This event is part of a sequence: a larger magnitude 3.4 struck 67 km away on Sep 2, 12:37 UTC, so this is most likely one of its aftershocks.
| Time (UTC) | Magnitude | Depth | Distance | Location |
|---|---|---|---|---|
| before | 3.1 | 3 km | 242 km | 10 km ENE of Coso Junction, CA |
| before | 1.5 | 13 km | 97 km | 5 km S of Loma Linda, CA |
| before | 1.2 | 7 km | 194 km | 16 km N of Indio, CA |
| before | 1.7 | 6 km | 162 km | 16 km WSW of Johannesburg, CA |
| before | 1.0 | 8 km | 81 km | 8 km N of Fontana, CA |
| before | 1.2 | 13 km | 169 km | 14 km SE of Anza, CA |
| before | 1.1 | 6 km | 135 km | 10 km N of Big Bear Lake, CA |
| before | 1.4 | 7 km | 159 km | 17 km WSW of Johannesburg, CA |
| before | 1.3 | 7 km | 161 km | 17 km WSW of Johannesburg, CA |
| before | 1.2 | 6 km | 162 km | 16 km WSW of Johannesburg, CA |
| before | 1.1 | 6 km | 145 km | 12 km W of Anza, CA |
| before | 1.1 | 8 km | 218 km | 19 km SSW of Ocotillo Wells, CA |
| before | 1.0 | 15 km | 141 km | 9 km WSW of Idyllwild, CA |
| before | 3.2 | 13 km | 12 km | 4 km SSE of Compton, CA |
| before | 1.0 | 16 km | 141 km | 8 km NW of Palomar Observatory, CA |
| before | 1.2 | 3 km | 161 km | 12 km S of Anza, CA |
| before | 1.0 | 3 km | 121 km | 7 km ENE of Running Springs, CA |
| before | 1.2 | 6 km | 145 km | 12 km W of Anza, CA |
| before | 1.1 | 5 km | 67 km | 6 km SE of Ontario, CA |
| before | 1.2 | 3 km | 197 km | 18 km NNE of Indio, CA |
| before | 1.4 | 7 km | 220 km | 10 km NNE of Ocotillo Wells, CA |
| before | 2.2 | 3 km | 221 km | 12 km NNE of Ocotillo Wells, CA |
| before | 1.8 | 15 km | 12 km | 1 km SSW of Bell, CA |
| before | 1.5 | 11 km | 25 km | 4 km SSE of Burbank, CA |
| before | 1.2 | 9 km | 177 km | 21 km N of Yucca Valley, CA |
| before | 2.7 | 10 km | 120 km | 4 km NE of Temecula, CA |
| before | 1.2 | 17 km | 143 km | 9 km SW of Idyllwild, CA |
| before | 0.9 | 10 km | 202 km | 19 km ESE of Julian, CA |
| before | 1.1 | 11 km | 202 km | 19 km ESE of Julian, CA |
| before | 1.7 | 10 km | 240 km | 13 km NW of Ocotillo, CA |
Frequently asked questions
How is earthquake magnitude measured?
Modern magnitudes are moment magnitudes (Mw), computed from the seismic moment: the area of the fault that slipped, how far it slipped and the rigidity of the rock. Each whole step up the scale is about 32 times more energy, so a magnitude 7 releases roughly a thousand times the energy of a magnitude 5.
What is the difference between magnitude and intensity?
Magnitude is one number for the whole earthquake, describing the energy released at the source. Intensity describes the shaking at a particular place, on the Modified Mercalli scale from I (not felt) to X+ (extreme), and falls off with distance from the epicenter.
What is an aftershock?
An aftershock is a smaller earthquake in the same area after a larger one, as the crust around the ruptured fault adjusts to the new stresses. They are most frequent in the first hours and days and fade over weeks to months, though a large mainshock can produce aftershocks for years.
Why do the magnitude and location change?
The first solution uses the nearest stations only. As recordings arrive from more seismographs around the world, USGS revises the magnitude, depth and epicenter, sometimes several times in the first hours. This page reflects the latest revision.
Where does this earthquake data come from?
From the U.S. Geological Survey’s real-time earthquake feeds, which combine the USGS National Earthquake Information Center with regional seismic networks worldwide. EarthBrowser ingests the feed every minute.